May 15, 2018 0 By admin

Connect the heat sink and fan assembly cable to the system board. To view details of a failure or to view a list of test results, use the following procedure from any test category screen: Before servicing a Lenovo product, be sure to read the Safety Information. Video card, if installed Video Signal failure 2. Re-start the test to reset the log file 1. SCSI adapter card, if installed 5.

Uploader: Mazull
Date Added: 5 December 2017
File Size: 10.75 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 54521
Price: Free* [*Free Regsitration Required]

Replacing The Fan Assembly M-tm the fan assembly This procedure describes how to remove and replace the lenovo mt-m 9851. Do not drop anything onto the microprocessor socket while it is exposed. Page 7 Appendix A.

Lenovo Thinkcentre Drivers Mt M Computers Laptop and Tablet Accessories – 01

Table of Contents Add to my manuals Add. Reconnect lenovo mt-m 9851 cables that were disconnected from the system board. Lenovo is committed to environmental leadership from operations to product design and recycling solutions. Install the new adapter into the appropriate leenovo on the system and close the adapter latch. Check power supply voltages 3. Flash the system and re-test.

There are no serviceable parts inside the device. Many customers have, near their equipment, rubber floor mats lenovo mt-m 9851 contain small conductive fibers to decrease electrostatic discharges. The failing system board must be returned with lenobo microprocessor socket cover to protect the pins during shipping and handling.

Lenovo ThinkCentre A57 – tower – Core 2 Duo E GHz – 2 GB – GB Overview – CNET

Replacing the power supply This mt–m describes how to remove and replace the power supply. Replacing The Microprocessor Ldnovo in den Strahl blicken. Chapter 10 Replacing FRUs Types,,, Page Some connectors on the rear of your computer are color-coded to help you lenovo mt-m 9851 where to connect the cables on your computer.

Install lenovo mt-m 9851 front panel card assembly into the chassis and secure it with the screw. Remove the retainer bracket from the failing diskette drive and install it mtt-m the lenovo mt-m 9851 diskette drive.

Replacing the power supply Attention Never remove the cover on a power supply or any part that has the following label attached. Press F3 to lwnovo the log file exceeded 2. Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. Press the diskette-drive lock at the side of the drive. Slide the drive bay assembly towards the rear of the chassis until it snaps into position. Video card, if installed Video Signal failure 2.


In the following index, X can represent any number. Selecting a startup device from the Startup Device menu does not lenovo mt-m 9851 change the startup sequence.

Lenovo M57e – ThinkCentre – 9481 Hardware Maintenance Manual

Lenovo mt-m 9851 the fan cable, power switch or LED cable, and temperature sensor cable from the system board. Connect the signal and power cables to the drive.

Power Supply RPL computer cannot access programs from its own hard 1. Replacing The Cmos Battery 4. Remove the game port device and re-test lenovo mt-m 9851 system XXX Game Port interface Test aborted by user Information only Re-start the test, if necessary Replacing The Power Supply 6. Push the memory module straight down into the memory connector until the retaining clips close.

Take note of the location of all cable connections on the system board and disconnect all cables. Install the new retention module if required on the new system board. Lift the heat sink and fan assembly off the failing system board. Found the problem, the motherboard lenovo mt-m 9851 been replaced some time ago.

I need both Ethernet, Lenovo mt-m 9851 and a few others.

To avoid a shock hazard: Page 21 Chapter 2 Safety information Pull on the blue handle to release and remove the hard disk drive lenovo mt-m 9851 the hard drive cage. Removing and replacing the front bezel This procedure describes how to remove and replace the front bezel.